Page 1 of 2 1 2 LastLast
Results 1 to 25 of 26

Thread: The Big 3

  1. #1
    Resident Flamer Registered Member -dh-'s Avatar
    Join Date
    Apr 2004
    Posts
    263

    The Big 3

    Perhaps someone should sticky this, so we can have something to refer to when recommending a big three upgrade.

    Anyways, found this at SoundDomain.

    :::
    :::

    As many of you know, upgrading the "Big 3" wires in your engine compartment can lower the overall resistance of your entire electrical system. The effects of the lower resistance are typically:

    1) Reduced dimming and smaller voltage drops
    2) More stable voltage and better current flow
    3) Less strain on your vehicle's charging system

    So for those of you looking for a cheap and easy way to upgrade your system and help out your electrical system without adding a high output alternator or an aftermarket battery, this is the modification for you. If you have heavy dimming or are getting large voltage drops during loud bass hits, but you don't have the money to spend on a high output alternator or a battery, upgrading your vehicle's "Big 3" will usually help to reduce and sometimes even eliminate the problems. So without further ado, the "Big 3" wires are:

    1) Battery negative to chassis
    2) Alternator to battery positive
    3) Chassis to engine

    Now, I suppose it would help if I explained what each of these wires does, and to do that I would like to paraphrase an explanation by IMTfox from a while ago: Think of your vehicle's charging system as two different circuits, one consisting of your amplifier and your battery, and the other consisting of your alternator and your battery. The current in your electrical system flows from your positive battery terminal to your amp, from your amp's ground to the chassis, and then from the chassis back to the negative battery terminal. But how does it get to the positive terminal in the first place? That's where the alternator comes in. Current in the second circuit flows from your alternator's positive post to the battery's positive terminal, then from the battery's negative terminal to the chassis, and from the chassis back to the block, which happens to be the grounding point for your alternator.

    So, from your battery, you have the power wire going to the power terminal on your amplifier and then your amplifier is grounded to the chassis of the vehicle. From here the current needs a way to get back to the negative battery terminal, and that way is through the first of the "Big 3," the battery negative to chassis wire. Upgrading this wire will "upgrade" the circuit between your battery and your amp by giving the current a larger path to flow through to get back to the battery.

    Now, think of your alternator as the battery and your battery as the amp. From the positive post on your alternator, you have the second of the "Big 3," the alternator to battery positive wire supplying "power" to your battery. From there the battery, just like your amp, is grounded to the chassis through the wire mentioned in the previous paragraph. Again, the current needs a way to get from the chassis back to the alternator's "negative terminal" and that way is through the last of the "Big 3," the chassis to engine wire. Since your alternator is most likely mounted to your engine block using a metal or conductive mounting bracket, you can simply add your new wire from the chassis to one of the mounting posts for the alternator. Upgrading these two wires will "upgrade" the circuit between your alternator and your battery, again giving the current a larger path to flow through.

    ----------------------------------------------

    Now that you understand exactly what the "Big 3" do, it's time to upgrade them to a larger gauge wire. You can use regular power wire from installing your car audio equipment, ring terminals, and crimping equipment just the same as you would for any other install. Let's start with the first of the "Big 3," the battery negative to chassis wire:

    1) Disconnect your battery's negative terminal and get the stock wiring out of the way. You might have to cut it and crimp a new ring terminal onto it. I found it helpful to use aftermarket battery terminals with multiple ports on them also.

    2) Scrape away the paint and drill the hole for your connection of the larger wire, or connect it to the stock grounding point. Either way you do it, make sure it is bare chassis metal, not covered by paint, and that the connection is as tight and secure as possible:

    -

    -

    3) Secure the new wire to the chassis and reconnect the vehicle's stock chassis ground, but DON'T reconnect the vehicle's negative battery terminal yet! You may find it helpful to cover the negative battery terminal with a cloth or other non-conductive material and just lay the terminal on it until you're ready to reconnect it later.

    Moving on to the next of the "Big 3," let's upgrade the alternator to battery positive wire:

    4) Locate the vehicle's alternator and look for a terminal post connected to it. The post shouldn't be hard to find. It should have only one wire connected to it, and it should lead to the positive terminal on the battery, possibly through the fuse box.

    -

    5) Disconnect the stock alternator to battery positive wire from the positive post and connect it to the post again with the new wire added.

    6) Run the wire either through your fuse box if applicable or through a fuse. The fuse should be sized to match the max ampacity of your wire, not the output capability of your alternator. As you can see I just went through the fuse box, so my upgrade is probably not making as much of a difference as it could if it were fused externally, but my alternator is capable of withstanding the draws anyway so I'm not particularly worried about it. If I ever begin to see a problem w/ current draws, I will probably fuse the wire externally with a 300A or so fuse...

    7) From the fuse, connect the wire to the positive terminal on your battery, again, leaving the stock wiring connected when you're done. The picture below shows the alternator to battery positive wire run from the alternator through my fuse box to the positive battery terminal.

    -

    Last, let's move to the chassis to engine wire: (Again, because your alternator is grounded to the block, all you need to do is find a bolt somewhere on the block and connect it to the chassis. The alternator's mounting bracket is usually a good place to find these bolts).

    8) Again, either drill a new hole or connect this wire to the stock chassis ground. From the chassis ground, run the wire back to one of the mounting posts for the alternator (or to a bolt on the engine block).

    -

    9) That's it! You're done. Reconnect the vehicle's negative battery terminal and check out the difference! Below is a shot of the "Big 3" upgraded in my car. The other wire you see coming out of the battery's positive terminal is obviously my amp's power wire.

    -

    ----------------------------------------------

    Helpful hints:

    1) Leave the stock wiring attached after you're done. Don't replace the stock wiring, add onto it. Current will take the path of least resistance anyway, so replacing the stock wire will only make more work for yourself.

    2) When fusing your alternator to battery positive wire, fuse it toward the battery end of the wire. As IMTfox points out later in this thread, the battery will explode if it's overloaded, while the alternator will only burn out its regulator which won't cause much damage except to the alternator itself. Exploding batteries are no fun!

    3) When crimping large gauge terminals for 1/0awg and sometimes even 4awg, a vice works well. Crimp one side of the terminal at a time, creating an overlapping edge. Put the boot around this and then wrap it in electrical tape if you want. the most secure connections will occur in this way.

    -

    -

    4) Lastly, prepare all your materials and tools BEFORE you are ready to upgrade. Know what you are doing before you start so you can be done as quick as possible. The majority of vehicles have computers that will reset after the battery is disconnected for a long time and they can cause older vehicles to do strange things if they reset.

    Hopefully this clears up most of the questions you had about why we upgrade the "Big 3" and how it helps to stop dimming and other electrical problems.
    Life's a heavy price to pay, but when you're dead, there's no complaining.

  2. #2
    Resident Cynic Registered Member FordXplod93's Avatar
    Join Date
    Dec 2003
    Location
    Peoria, IL
    Posts
    616
    Great find, dh. Consider it stickied. ;)

    ~FordX
    Often imitated, never duplicated.

  3. #3
    Resident Flamer Registered Member -dh-'s Avatar
    Join Date
    Apr 2004
    Posts
    263
    Quote Originally Posted by FordXplod93
    Great find, dh. Consider it stickied. ;)

    ~FordX

    cool
    Last edited by -dh-; 08-05-2004 at 21:01.
    Life's a heavy price to pay, but when you're dead, there's no complaining.

  4. #4
    Junior Member Registered Member
    Join Date
    Aug 2004
    Posts
    6
    thats pretty cool because it just confirms what my friend and i were discussing about upgrading to my system since caps are overrated and replacing those 3 wires would be a cheap way to lessen dimming of my lights.

  5. #5
    Junior Member Registered Member
    Join Date
    Sep 2004
    Posts
    4

    the BIG THREE ooo LoLZ

    ok so who here who has passed elementary science and knows even a little bit about electricity doesnt know that bigger wires allow for more flow or that other materials pass electricity better...? thanks a bunch. great forum... lots of help with my system. keep posting

  6. #6
    Junior Member Registered Member
    Join Date
    Jan 2006
    Posts
    1

    ...but is it enough?

    So are you saying that if i did the big three i would have all the power i needed at top volume if i have a 1400W amp?

  7. #7
    Resident Cynic Registered Member FordXplod93's Avatar
    Join Date
    Dec 2003
    Location
    Peoria, IL
    Posts
    616
    Quote Originally Posted by shnoob
    So are you saying that if i did the big three i would have all the power i needed at top volume if i have a 1400W amp?
    Wires don't give you more power, they just allow for easier flow of existing power. More power is generated from upgrading your battery and alternator.

    ~FordX
    Often imitated, never duplicated.

  8. #8
    Shifty Registered Member Derek_Thompson24's Avatar
    Join Date
    May 2006
    Location
    Canada
    Posts
    28

    Thank You!!

    Damnit ive been looking for the answer for so long. Recently my deck has been cutting out and my engine has almost been stalling. I'm going to try changing those three wires because it can't hurt. If that doesn't help i am going to buy a 200 dollar battery though. Thanks alot!
    Shifty

  9. #9
    I'm in your head Registered Member CVStroker's Avatar
    Join Date
    Oct 2002
    Location
    Madison WI
    Posts
    2,280
    A new battery wont help when the car is running, you need a new alternator if you are drawing that much juice
    Life: It's the ultimate sin; a game with no rules that you're expected to win

  10. #10
    Junior Member Registered Member
    Join Date
    Sep 2009
    Posts
    2
    Thanks a lot for this upgrade. It is really a great help.

  11. #11
    Junior Member Registered Member
    Join Date
    Nov 2009
    Posts
    5
    hey i am worried if this big 3 causes any sort of internal problem...is it possible...
    Michl87 Best Cigars

  12. #12
    CAR REVIEW ADMlN Registered Member Easy E's Avatar
    Join Date
    Dec 2003
    Location
    WA
    Posts
    2,392
    What do you mean internal problem? Please explain.
    Thats my 2 cents.

  13. #13
    Junior Member Registered Member
    Join Date
    Dec 2009
    Posts
    13

    Carnut1420

    it's quite a big post. but informational too


    dupontregistry

  14. #14
    Junior Member Registered Member
    Join Date
    May 2010
    Posts
    2
    thanks for posting i like this

    To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


    To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


    To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


    To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

  15. #15
    Junior Member Registered Member
    Join Date
    May 2010
    Posts
    1
    Quote Originally Posted by -dh-
    Perhaps someone should sticky this, so we can have something to refer to when recommending a big three upgrade.

    Anyways, found this at SoundDomain.

    :::
    :::

    As many of you know, upgrading the "Big 3" wires in your engine compartment can lower the overall resistance of your entire electrical system. The effects of the lower resistance are typically:

    1) Reduced dimming and smaller voltage drops
    2) More stable voltage and better current flow
    3) Less strain on your vehicle's charging system

    So for those of you looking for a cheap and easy way to upgrade your system and help out your electrical system without adding a high output alternator or an aftermarket battery, this is the modification for you. If you have heavy dimming or are getting large voltage drops during loud bass hits, but you don't have the money to spend on a high output alternator or a battery, upgrading your vehicle's "Big 3" will usually help to reduce and sometimes even eliminate the problems. So without further ado, the "Big 3" wires are:

    1) Battery negative to chassis
    2) Alternator to battery positive
    3) Chassis to engine

    Now, I suppose it would help if I explained what each of these wires does, and to do that I would like to paraphrase an explanation by IMTfox from a while ago: Think of your vehicle's charging system as two different circuits, one consisting of your amplifier and your battery, and the other consisting of your alternator and your battery. The current in your electrical system flows from your positive battery terminal to your amp, from your amp's ground to the chassis, and then from the chassis back to the negative battery terminal. But how does it get to the positive terminal in the first place? That's where the alternator comes in. Current in the second circuit flows from your alternator's positive post to the battery's positive terminal, then from the battery's negative terminal to the chassis, and from the chassis back to the block, which happens to be the grounding point for your alternator.

    So, from your battery, you have the power wire going to the power terminal on your amplifier and then your amplifier is grounded to the chassis of the vehicle. From here the current needs a way to get back to the negative battery terminal, and that way is through the first of the "Big 3," the battery negative to chassis wire. Upgrading this wire will "upgrade" the circuit between your battery and your amp by giving the current a larger path to flow through to get back to the battery.

    Now, think of your alternator as the battery and your battery as the amp. From the positive post on your alternator, you have the second of the "Big 3," the alternator to battery positive wire supplying "power" to your battery. From there the battery, just like your amp, is grounded to the chassis through the wire mentioned in the previous paragraph. Again, the current needs a way to get from the chassis back to the alternator's "negative terminal" and that way is through the last of the "Big 3," the chassis to engine wire. Since your alternator is most likely mounted to your engine block using a metal or conductive mounting bracket, you can simply add your new wire from the chassis to one of the mounting posts for the alternator. Upgrading these two wires will "upgrade" the circuit between your alternator and your battery, again giving the current a larger path to flow through.

    ----------------------------------------------

    Now that you understand exactly what the "Big 3" do, it's time to upgrade them to a larger gauge wire. You can use regular power wire from installing your car audio equipment, ring terminals, and crimping equipment just the same as you would for any other install. Let's start with the first of the "Big 3," the battery negative to chassis wire:

    1) Disconnect your battery's negative terminal and get the stock wiring out of the way. You might have to cut it and crimp a new ring terminal onto it. I found it helpful to use aftermarket battery terminals with multiple ports on them also.

    2) Scrape away the paint and drill the hole for your connection of the larger wire, or connect it to the stock grounding point. Either way you do it, make sure it is bare chassis metal, not covered by paint, and that the connection is as tight and secure as possible:

    -

    -

    3) Secure the new wire to the chassis and reconnect the vehicle's stock chassis ground, but DON'T reconnect the vehicle's negative battery terminal yet! You may find it helpful to cover the negative battery terminal with a cloth or other non-conductive material and just lay the terminal on it until you're ready to reconnect it later.

    Moving on to the next of the "Big 3," let's upgrade the alternator to battery positive wire:

    4) Locate the vehicle's alternator and look for a terminal post connected to it. The post shouldn't be hard to find. It should have only one wire connected to it, and it should lead to the positive terminal on the battery, possibly through the fuse box.

    -

    5) Disconnect the stock alternator to battery positive wire from the positive post and connect it to the post again with the new wire added.

    6) Run the wire either through your fuse box if applicable or through a fuse. The fuse should be sized to match the max ampacity of your wire, not the output capability of your alternator. As you can see I just went through the fuse box, so my upgrade is probably not making as much of a difference as it could if it were fused externally, but my alternator is capable of withstanding the draws anyway so I'm not particularly worried about it. If I ever begin to see a problem w/ current draws, I will probably fuse the wire externally with a 300A or so fuse...

    7) From the fuse, connect the wire to the positive terminal on your battery, again, leaving the stock wiring connected when you're done. The picture below shows the alternator to battery positive wire run from the alternator through my fuse box to the positive battery terminal.

    -

    Last, let's move to the chassis to engine wire: (Again, because your alternator is grounded to the block, all you need to do is find a bolt somewhere on the block and connect it to the chassis. The alternator's mounting bracket is usually a good place to find these bolts).

    8) Again, either drill a new hole or connect this wire to the stock chassis ground. From the chassis ground, run the wire back to one of the mounting posts for the alternator (or to a bolt on the engine block).

    -

    9) That's it! You're done. Reconnect the vehicle's negative battery terminal and check out the difference! Below is a shot of the "Big 3" upgraded in my car. The other wire you see coming out of the battery's positive terminal is obviously my amp's power wire.

    -

    ----------------------------------------------

    Helpful hints:

    1) Leave the stock wiring attached after you're done. Don't replace the stock wiring, add onto it. Current will take the path of least resistance anyway, so replacing the stock wire will only make more work for yourself.

    2) When fusing your alternator to battery positive wire, fuse it toward the battery end of the wire. As IMTfox points out later in this thread, the battery will explode if it's overloaded, while the alternator will only burn out its regulator which won't cause much damage except to the alternator itself. Exploding batteries are no fun!

    3) When crimping large gauge terminals for 1/0awg and sometimes even 4awg, a vice works well. Crimp one side of the terminal at a time, creating an overlapping edge. Put the boot around this and then wrap it in electrical tape if you want. the most secure connections will occur in this way.

    -

    -

    4) Lastly, prepare all your materials and tools BEFORE you are ready to upgrade. Know what you are doing before you start so you can be done as quick as possible. The majority of vehicles have computers that will reset after the battery is disconnected for a long time and they can cause older vehicles to do strange things if they reset.

    Hopefully this clears up most of the questions you had about why we upgrade the "Big 3" and how it helps to stop dimming and other electrical problems.
    nice info bro. very detailed. i use Auto Meter for my gauge though.

  16. #16
    Junior Member Registered Member
    Join Date
    Aug 2010
    Posts
    11

    Thinking

    Hmm. Let me think about it. I’m not quite sure if I’m going to upgrade to electrical system because I don’t know what will happen if I do. I might encounter some problems.
    throttle body spacer

  17. #17
    Junior Member Registered Member
    Join Date
    May 2008
    Posts
    17
    Cool

    To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

  18. #18
    Junior Member Registered Member
    Join Date
    May 2017
    Posts
    3
    The blog post is very interesting to me. There is much useful info. Thanks

    To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
    -
    To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

  19. #19
    Junior Member Registered Member
    Join Date
    Mar 2018
    Posts
    10
    These are the things that we need to prioritize whenever we make an upgrade.

  20. #20
    Junior Member Registered Member
    Join Date
    Mar 2019
    Posts
    7

    316 Auto Salon

    And lastly...lie! There was way more, very valuable and extremely elaborate, however,

  21. #21
    Banned User
    Join Date
    Jul 2019
    Posts
    19
    What was more there? I dont understand

  22. #22
    Junior Member Registered Member
    Join Date
    Jul 2019
    Posts
    10

    The Big 3

    What timing, George Emma bought the entire Crime Story series on DVD. We just watched the last episode a few nights ago. When it comes to the big or small screen, Crime Story has got to be numero uno in the cool music department. The series was great, too ... very addictive.

  23. #23
    Junior Member Registered Member
    Join Date
    Dec 2019
    Posts
    9
    Quote Originally Posted by FordXplod93 View Post
    Great find, dh. Consider it stickied. ;)

    ~FordX
    What is glued?

  24. #24
    Junior Member Registered Member
    Join Date
    Dec 2019
    Posts
    9
    Quote Originally Posted by copternadley View Post
    nice info bro. very detailed. i use Auto Meter for my gauge though.
    Yes i think there are several options

  25. #25
    Junior Member Registered Member
    Join Date
    Feb 2020
    Posts
    3

    Good

    It sounds good.

Thread Information

Users Browsing this Thread

There are currently 88 users browsing this thread. (0 members and 88 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •