Results 1 to 6 of 6

Threaded View

  1. #1
    CAR REVIEW ADMlN Registered Member Easy E's Avatar
    Join Date
    Dec 2003
    Location
    WA
    Posts
    2,392

    Amplifier Settings Tutorial: Gain, Subsonic filter, Crossover, Bass Boost, Fuses etc

    Gain:
    Gain is like a volume knob on a stereo. More you turn it up more the stereo will amplify the input signal. The problem is your input signal can exceed the amplifiers output. The signals will then clip which causes distortion and no more power out of the amp. Problem is each HU has a different output of a signal, so the amplifiers gain needs to match that input signal.

    Like in my stereo in my truck, I have my gain like 15% up. That way when I reach 45-50 on my HU the amp is about maximum power. Now if I had my gain all the way up then the max I will be able to turn my HU is to about 15 or so before I reach max power output.

    Input Sensitivity
    Same thing as Gain.

    Crossover:
    Crossovers limit frequencies going to a subwoofer. Higher order like 4th order instead of 2nd order, steeper the slope is of the crossover more effective it is. Crossovers gradually reduce frequencies. For more information check out this link.
    http://www.bcae1.com/xovrslop.htm
    Set woofer crossovers low pass 60-100hz depending on the sub midbass etc. 80hz is a good area.
    Set the high pass crossover for your speakers to the same number as your woofer typically around 80hz.

    Subsonic Filter:
    Now Subsonic filter is a crossover, that limits extreme low bass going to your subwoofers. if you are running sealed set it as low as possible if you are running ported set it 5-10hz bellow your tuning of your sub.

    Mode/Slope
    Setting the steepness of the crossover slope. See Crossover

    Infrasonic Filter:
    This is the same thing as Subsonic Filter. Commonly found on JL amps.

    Phase:
    Phase changes the relative phase of the outputs on the amplifier. This is not that helpful in most situations.

    Bass Boost
    This amplifies a certain frequency. Sometimes it has set, usually around 40 Hz other amps have a variable frequency rang. The higher the bass boost is set more the amplifier boost a certain frequency. In typical installations, bass boost is not recommended to be on.

    [B]Center Frequency:[B]
    This is found on many JL Audio amps, it is where you want the bass boost to kick in. See EQ.

    EQ
    This is like a bass boost, but usually is variable. Don't worry about this.

    [B]Width/Q/B]
    This is for EQing, smaller the Q more gradual the slope is for EQing. Usually you do not mess with this since you do not use the EQ on the amplifier.

    Power Wire
    10 GA wire is good to about 200-watt amplifier
    8 GA wire is good to about 500 watt amplifier
    4 GA wire is good to about 1000 watt amplifier
    2 GA wire is good to about 1700 watt amplifier
    1 GA good to about 2200 watt amplifier
    0 GA is good to about 3000 watt amplifier.
    These are rough numbers and depends on how long the power wire is ran.

    Ground Wire
    Try to make this as short as possible. The shorter the better. Keep it shorter then 3 ft or alternator wine can happen. Also, try to keep it the same GA as your power wire.

    Fuses
    Use only the same size fuses as your amp recommends. For fusing the power wire go with about 10 amp higher then all the components fuses combined running off that power wire. Fuse 6-18" from the battery, any shorter can cause corrosion, and any farther can be risky.
    Last edited by Easy E; 03-28-2006 at 19:50.
    Thats my 2 cents.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •